Required Employee Supplied Tool List

Complete the form below for the Required Employee Supplied Tool List Form.




  • Electricians Tool Belt (No Pouch Sling types)
  • 9" Side cutters (Lineman's Pliers)
  • 8" Diagonal cutters ("Dikes")
  • 8" Needle-nose Pliers
  • Wire Stripper & Cutter - 10-20AWG Solid
  • Aviation snips, Offset snip -straight cut
  • Adjustable Wrenches
    • (1) 6" Size, (1) 10" Size
  • Slip Joint Pliers (Tongue and Groove)
    • (1) Pair of 430 (10") size, (1) Pair of 440 (12") size
  •  Common Screwdrivers Assorted
    • (1) 1/4" Common (Large), (1) 3/16" Common (Medium), (1) 1/8" Common (Trim)
  •  Phillips Screwdrivers Assorted
    • (1) #1 Size Phillips, (1) #2 Size Phillips, (1) #3 Size Phillips
  •  Scratch Awl (Center punch)
  • Electricians Hacksaw
  • Jab "Keyhole" Drywall Saw
  • Electricians or Utility Knife
  • Claw Hammer (16-20oz)
  • Tape Measure (25-30ft)
  • 9" Magnetic Topedo Level
  • Roto-split MC Cable cutting tool
  • Flashlight
  • Hex Key Folding sets
    • (1) Metric set, (1) SAE Standard set
  •  7 Piece Hollow Shaft Nut Driver Set
    • (1) Metric Set, (1) SAE Standard set
  •  Voltage Tester (Non-Battery Powered)
    • "Ideal Vol-Test" #61-065, "KLEIN AC/DC Voltage Tester" #ET60 or equivalent
  •  Cordless Drill Set - Impact Tool and Drill/Driver Tool w/ Batteries and Charger, 18V Min
  • ANSI Rated Work Boots (Non-Steel toe) Composite Toe -OK

Professional Service is one of our nation's most honored and sought-after careers.

Work hard and take pride in your career as a service provider.


JOURNEYMAN LEVEL + (In addition to the apprentice level required tools)

  • Fuse Puller
  • Chaulk Box (Reel Line kit), laser line tool
  • Plumb Bob or laser level
  • Digital or Analog Multi-Meter, 600A, W/ Clamp and Probe Kit
  • Mechanics Tool Set Metric and SAE with 1/4"-1/2" Drive Ratchets
  • Knock-out Punch set 1/2" -2" Cut
  • Slip Joint Pliers (Tongue and Groove)
    • (1) Pair of 460 (16.5") size
  •  100' Tape Measure
  • NEC Code Book (Current Edition)
  • Local Code Requirements (SA, Chapter X)

Any Additional Local Code Requirements




  • Hard Hat
  • Safety Vest
  • Cut-Resistant Gloves
  • Leather Gloves
  • Safety Glasses
  • Ear Plugs
  • PFAS (Personal Fall Arrest System) consisting of Full Body Harness, Lanyard & SRL (Yo-Yo)

All equipment should be stored in a manner to not be damaged and the PFAS should be hung if possible. Lastly, PPE should be cleaned regularly and replaced when needed.

*Not required for Apprentices / Helpers with < 5 years experience in the electrical trade

I have read and understood the tool list requirements. I agree to acquire and maintain the tools listed above. I understand that my tools are my responsibility and are not covered by the company’s insurance. I understand that the required tools need to be available to me during all working hours and that they need to be in good and safe working order.

MM slash DD slash YYYY